EV High Voltage Harness Assembly — Custom 600/1000/1500 V DC Battery Pack and Motor Harness with Crimped Copper Lugs, XLPE or Silicone Cable, VW-1 Flame Rating, and IP67 Mated Sealing
EV-laad- en Hernieuwbare-energiekabels /EV High Voltage Harness Assembly

EV High Voltage Harness Assembly — Custom 600/1000/1500 V DC Battery Pack and Motor Harness with Crimped Copper Lugs, XLPE or Silicone Cable, VW-1 Flame Rating, and IP67 Mated Sealing

Custom 600/1000/1500 V DC EV high voltage harness assemblies with crimped copper lugs, XLPE or silicone cable, VW-1 flame rating and IP67 mated sealing.

Belangrijkste Kenmerken

Three DC voltage classes in one build family — 600 V, 1000 V, and 1500 V DC, so a single harness drawing set can cover a 400 V pack, an 800 V-class pack, and a 1500 V storage string without changing the lug or connector family
Oxygen-free copper conductor in finely stranded construction — the strand bundle stays flexible enough to route around battery pack frames and motor mounts while carrying the full circuit current
Crimped copper lugs instead of soldered joints — the cable-to-terminal joint is mechanically compressed, so the assembly resists the vibration and thermal cycling that a battery pack sees in service
Current carrying capacity from 20 A to 300 A — sized by cross-section, which spans 25 mm² to 120 mm² depending on the circuit
Temperature rating selectable by compound — −40 °C to +125 °C, +150 °C, or +180 °C, chosen to match the heat soak at the pack, the inverter, or the motor
IP67 in the mated condition — the connector pair is sealed against dust ingress and temporary immersion when fully engaged, which is the state that matters inside a pack enclosure
VW-1 flame rating and RoHS compliance — the flame rating is a vertical wire flame test, relevant where a harness passes through a compartment shared with other electrical equipment
Built to drawing or sample — conductor size, harness length, lug bore, lug orientation, cable-entry angle, insulation colour, and connector keying are all specified by the customer

Toepassingen

Battery pack interconnection — module-to-module and pack-to-junction links inside the traction battery enclosure, including the main positive and main negative runsMotor and inverter power — three-phase power harnesses between the inverter and the traction motor, in 35, 70, and 95 mm²High voltage distribution box to battery — the main power path from the PDU to the pack, in 35, 50, and 70 mm²PTC heater and auxiliary high voltage loads — cabin heating circuits and other high voltage auxiliaries that draw from the traction busContainerized battery energy storage — inter-rack and rack-to-PCS power harnesses in utility-scale and commercial storage containersCommercial, industrial, and residential BESS — cabinet-to-cabinet power links where a pre-terminated harness replaces field crimpingTelecom base station and mobile storage — compact high voltage links in cabinets where a factory-made assembly removes on-site termination riskRail transit and marine storage — power harnesses for auxiliary storage and traction support systems

Technische Specificaties

Product Type EV high voltage harness assembly — factory-built cable harness with crimped lugs and connectors
Rated Voltage 600 V DC / 1000 V DC / 1500 V DC, selected per circuit
Conductor Material Oxygen-free copper, multi-strand finely stranded
Cross-Section Range (General) 25, 35, 50, 70, 95, 120 mm² (other sizes on request)
Cross-Section (Three-Phase Motor Harness) 35, 70, 95 mm²
Cross-Section (Battery Pack Harness) 35, 50, 70 mm²
Current Carrying Capacity 20–300 A at the 1500 V rating, determined by cross-section and installation method
Cable Compound Options PVC, silicone, XLPO, or XLPE — selected per temperature and flexibility requirement
Temperature Rating −40 °C to +125 °C, +150 °C, or +180 °C depending on the compound selected
Flame Rating VW-1
Ingress Protection IP67 in the mated condition (connector fully engaged)
Termination Crimped copper lugs; lug bore, opening direction, and cable-entry angle customizable
Harness Types Battery pack harness, three-phase power harness, high voltage corrugated conduit harness, waterproof EV harness, adapter harness, energy storage harness
Conductor Finish Bare oxygen-free copper
RoHS RoHS compliant
Certifications CE and RoHS listed; CCC, UL, ISO, and SAA markings also listed by the supplier — confirm the certificate required for your target market before ordering
Customization Built to drawing or sample; conductor size, length, lug type, colour, and connector keying specified by the customer
Packing Bulk cable 100 m per coil, cut lengths below 100 m supplied as measured lengths; finished harnesses packed to drawing
Application (Vehicle) Battery pack interconnection, motor and inverter power, PTC heater, chassis high voltage routing, battery terminal links
Application (Energy Storage) Containerized BESS, commercial and industrial storage, residential storage, telecom base station storage, mobile storage, marine storage

Gedetailleerde Beschrijving

What an EV High Voltage Harness Assembly Does

An EV high voltage harness assembly is the finished power path between the traction battery and the equipment that draws from it. It is not bulk cable sold by the metre: the conductors are cut to length, stripped, fitted with crimped copper lugs or high voltage connectors, and sealed, so the part arrives ready to bolt into the pack, the distribution box, or the inverter.

The distinction matters at build time. A field-crimped joint depends on the tooling and the operator at the assembly station, and a poor crimp shows up later as a hot joint under load. A factory assembly moves that joint into a controlled press with a fixed crimp height, and the part arrives with the termination already made.

Three DC voltage classes are available in the same build family — 600 V, 1000 V, and 1500 V DC. A single drawing set can therefore cover a 400 V pack, an 800 V-class pack, and a 1500 V storage string without changing the lug or connector family.

How the Harness Is Built

The construction runs from the conductor outward, and each layer is chosen against a specific condition rather than by default.

  • Conductor — oxygen-free copper in a multi-strand finely stranded construction. The fine stranding keeps the bundle flexible enough to follow the routing around a pack frame or a motor mount, while the copper cross-section carries the circuit current.
  • Insulation and sheath — PVC, silicone, XLPO, or XLPE. The compound sets the temperature class and the flexibility, so it is selected with the routing in mind, not only with the current.
  • Termination — crimped copper lugs. The lug bore, the opening direction, and the cable-entry angle are all set on the drawing, because a lug that fits the stud but enters at the wrong angle will not dress against the pack wall.
  • Sealing — the connector pair reaches IP67 when mated. The seal is a property of the engaged pair, not of either half alone.
  • Flame — VW-1 rated, a vertical wire flame test that matters where the harness shares a compartment with other electrical equipment.

Electrical and Thermal Ratings

ParameterValue
Rated voltage600 / 1000 / 1500 V DC
Current carrying capacity20–300 A at 1500 V
Cross-section, general range25–120 mm²
Cross-section, three-phase motor harness35 / 70 / 95 mm²
Cross-section, battery pack harness35 / 50 / 70 mm²
ConductorOxygen-free copper, finely stranded
Temperature rating−40 °C to +125 °C / +150 °C / +180 °C
Flame ratingVW-1
Ingress protectionIP67, mated
Conductor finishBare copper

The current figure is a range rather than a single number because the same 1500 V assembly can be built at 25 mm² or at 120 mm². The cross-section and the installation method together set the continuous current, so the two are specified together on the drawing.

Harness Configurations for Battery Packs, Motors, and Energy Storage

Six build forms are covered, and they differ in termination and routing rather than in conductor:

  • Battery pack harness — module links and the main positive and main negative runs, in 35, 50, and 70 mm², terminated with lugs sized to the pack studs.
  • Three-phase motor power harness — inverter to motor, in 35, 70, and 95 mm², carrying the full drive current.
  • High voltage corrugated conduit harness — the cable run is protected by a corrugated conduit where it passes along the underbody or through a shared compartment.
  • Waterproof EV harness — sealed connector bodies for routes exposed to splash or wash-down.
  • Adapter harness — transitions between two connector standards or between a connectorised end and a lug end.
  • Energy storage harness — inter-rack and rack-to-PCS power links, including the main positive and main negative runs inside a storage container.
The energy storage forms serve containerized battery systems, commercial and industrial cabinets, residential storage, telecom base station storage, mobile storage, and marine storage. The vehicle forms serve battery pack interconnection, motor and inverter power, PTC heating, chassis routing, and battery terminal links.

Specifying a Custom Harness

Because the part is built to drawing, the specification has to carry more than a cross-section and a length. The items below are the ones that change the build:

  • Conductor cross-section per circuit, and the number of circuits in the harness
  • Harness length, measured from lug face to lug face rather than along the cable
  • Lug bore diameter, opening direction, and cable-entry angle
  • Connector type and keying, and which end is connectorised
  • Voltage class — 600, 1000, or 1500 V DC
  • Temperature class — 125 °C, 150 °C, or 180 °C
  • Insulation colour, and any marking or label required on the assembly
  • Whether the route needs corrugated conduit or a sealed connector body
A drawing or a physical sample is enough to start. Where a drawing is not yet available, the sample plus the circuit current and the installation temperature is sufficient to fix the conductor and the compound.

Certification and Market Requirements

The assemblies are supplied with CE and RoHS compliance, and the supplier lists CCC, UL, ISO, and SAA markings as well. Certification is market-specific: a harness that ships into the EU is documented against CE, while a North American build needs the UL file, and a Chinese domestic build needs CCC. Confirm the certificate required for the destination market before the order is placed, and the documentation is matched to that market rather than assumed.

Choosing the Right Harness for Your Build

The selection comes down to three questions. What is the circuit voltage — 600, 1000, or 1500 V DC? What current must the conductor carry continuously, which sets the cross-section between 25 mm² and 120 mm²? And what is the temperature at the termination point, which sets the compound and the 125 °C, 150 °C, or 180 °C class?

Answer those three, add the routing length and the lug or connector details, and the harness can be quoted against a drawing. Send the circuit diagram, the sample, or the parameter list through the enquiry form on this page and the assembly is specified from there.

Veelgestelde Vragen

Can you build a harness to my drawing rather than to a catalogue size?

Yes. The assembly is built to drawing or to a physical sample. Send the circuit diagram or the sample with the conductor cross-section, harness length, lug bore and orientation, cable-entry angle, and connector type. Colour and marking can be specified as well. There is no fixed catalogue length — the length is part of the drawing.

Which voltage class should I specify for an 800 V platform?

The 1000 V DC class covers an 800 V-class pack with headroom. The 1500 V DC class is used where the harness also serves a 1500 V storage string or where a single part number is preferred across vehicle and storage builds. The 600 V DC class suits lower-voltage auxiliary and 400 V circuits.

Is the IP67 rating valid before the connector is mated?

No. The IP67 rating applies to the mated condition, with the connector pair fully engaged. An unmated connector end is not sealed to IP67. If the harness is shipped with an open end, that end needs a cap or a sealed connector for storage and transit.

How is the temperature class chosen between 125 °C, 150 °C, and 180 °C?

It follows the compound and the heat soak at the installation point. Silicone and XLPO builds reach the higher classes, while PVC and standard XLPE sit at the lower end. Tell us the ambient temperature at the pack, inverter, or motor, and the class is matched to it rather than assumed.

Do you supply the harness with the connector, or only the cable with lugs?

Both forms are available. The assembly can be supplied as cable with crimped copper lugs only, or with the high voltage connector fitted at one or both ends. Specify which end is connectorised and which is lug-only on the drawing.

Product Aanvraag

Product: EV High Voltage Harness Assembly — Custom 600/1000/1500 V DC Battery Pack and Motor Harness with Crimped Copper Lugs, XLPE or Silicone Cable, VW-1 Flame Rating, and IP67 Mated Sealing

Technische specificaties toevoegen (optioneel)

Hoe meer details u geeft, hoe sneller en nauwkeuriger onze offerte is.

Geen bestand gekozen

PDF, Office, afbeelding of CAD-bestand — max. 5 MB

Hulp Nodig?

Certificeringen

ISO 9001
Kwaliteit
CE
Europees
RoHS
Milieu
TÜV
Certificering

Offerte Nodig voor Dit Product?

Stuur ons uw vereisten en ontvang binnen 24 uur een gedetailleerde offerte.